The 10 Scariest Things About Car Key Button Repair

Car Key Button Repair

A damaged car key button can be frustrating. You may need to call an emergency locksmith service that is available 24 hours a day for assistance or to purchase a new remote.

But, you may be able to save money by fixing an old key fob instead of replacing it. This is particularly true if the switch is worn out or has faulty contacts are at the root of the issue.

Battery

If the buttons on the key fob aren't responding to pressing, it could be an obvious indication that your battery is dead or nearing the end of its lifespan. Fortunately replacing the battery is an easy task that you can complete on your own rather than hiring a locksmith to complete the task for you.

Find the battery compartment first. It is usually located on the back of the key fob and could be hidden behind the cover, which slides out, or an access point that opens when you push the button. When the compartment is open you can look for the tiny button-cell battery. It's usually the shape of an ordinary coin and is identified with a plus and the minus symbol. Take the battery out and insert a new one in its place, making sure that the plus and minus signs are aligned correctly.

Close the compartment and snap the two halves of your key repair car fob. Be sure to align the parts and snap them into place properly prior to closing the door and testing your keys. To verify that the buttons work properly Press any of them.

If your remote key fob stops working even after you replace the battery, it may be suffering from other issues that require a different kind of repair. Physical damage from dropping the fob into a puddle, for example could cause it to cease functioning altogether. It could also be a problem with the internal electrical system or the need to be deprogrammed. See if you can find out if the problem is with your key fob applying these other typical automotive troubleshooting methods.

Switches

There are a variety of switches found in the car keys repairs key fob dependent on the year and make. The older style of key usually has a separate chip that is visible in the case, while the newer keys are more advanced and function by sending signals to the car. The buttons on a key can be worn out or damaged due to regular use, irrespective of the model. They become hard to press or not responsive. If you attempt to press the button too hard, it can cause further damage and potentially stop the key from being able to start your vehicle in the future.

If your auto key fob repair doesn't seem to be working, first try changing the battery. If that doesn't work, you may need to clean your key fob and re-adjust the switches. These tiny electronic switches are more prone than the larger parts of the key to break due to the fact that they are constantly tossed about.

The switches are rubber-like and are coated with an electricity conducting film that can wear down over time. Fortunately, they are also small and inexpensive to replace. The old ones are soldered onto the circuit board, so you'll have to take care to remove them without damaging anything else. You can then solder the new ones into and reassemble the fob.

Do not use your car key fob for more than a couple of hours at a time, and avoid leaving it visible. If you're not using your key, put it away in a secure location.

If you've already tried cleaning your key fob or replacing the battery, but the issue persists it's time to consider a locksmith. A professional locksmith can check the frequency of your key to determine whether your car is able to communicate. They can also open and replace microswitches as well as change cases, and more.

Outer Case

A key fob spends much of its time bouncing around and if the buttons aren't free to move between the case they can get stuck or break. If cleaning the case with rubbing alcohol and a cotton swab doesn't work, it may be necessary to remove the case. If the contacts that the buttons touch are not a good fit or if they're damaged, adjusting them could be the only solution.

Rubber buttons can be worn out over time. Rubber buttons can become hard to press as they stretch, and nails can gouge them. In this case, the key may fail, and it's time to replace the case or buttons. This repair involves removing the remote, finding the buttons on the circuit board, then heating the solder, and then carefully removing them. The circuit board is soldered with new buttons. The case can be rebuilt and the horseshoe key blade piece can be attached. The new buttons must be snugly fitted inside the case to avoid them from falling out.

Inner Case

Since your key fob is prone to get jostled around and may occasionally be pressed by accident and the buttons inside may get damaged or stuck over time. If your key fob isn't working while you are away from home, you can solve the issue quickly using metallic tape and a punch hole. This allows you to unlock doors, but not start the car remote key repair shop near me. This simple fix can enable you to safely make it back to your vehicle and finish your trip.